- ✅ Ready to use — no mixing required
- ✅ Rapid-drying — touch-dry in 1–2 hours
- ✅ Keys onto epoxy, polyurethane, polyurea and fibreglass surfaces
- ✅ Fully compatible with TAL cementitious underlayments and screeds
- ✅ Coverage ±5.5m² per litre (±27.5m² per 5L bucket)
When to Use TAL Primercoat
Use TAL Primercoat when laying a cementitious underlayment or screed over any resin-based surface — existing or newly applied epoxy coatings, polyurethane floors, polyurea, fibreglass, and similar impervious substrates. Without a keying slurry, cementitious products cannot bond to the smooth resin surface and will delaminate.
Pack Contents & Coverage
- Pack: 5L (7.5kg) ready-mix plastic bucket — no mixing required
- Coverage: ±5.5m² per litre / ±27.5m² per bucket (per coat)
- Application thickness: 0.2mm – 1mm
- Colour: light green wet, dries to grass-green
- Actual coverage will vary depending on surface profile and site conditions
Application
- Surface preparation (existing resin surfaces): Diamond grind to remove all dirt, grease and surface contaminants and produce an open, lightly textured surface. Solvent wipe with TAL Epoxy Cleaning Fluid.
- Clean: Vacuum or sweep all dust and loose particles thoroughly. Vacuuming is preferred.
- Stir well before use. Do not dilute with water or add any additives.
- Apply with a short-pile lambswool roller, ensuring 100% coverage of the substrate. Any gaps in coverage can result in delamination of the following layer.
- Allow to dry for 1–2 hours at 23°C / 50% RH until touch-dry with no visible transfer when rubbing over the surface.
- Apply TAL cementitious underlayment or screed compound directly onto the dried Primercoat.
Note: TAL Primercoat cures by water evaporation. Thicker applications, cold conditions or poor ventilation will extend drying time. Do not apply below 10°C or above 30°C. Do not dilute or adulterate the product in any way.
Important: For installations on post-tensioned concrete suspended slabs where significant building movement is anticipated, a wet epoxy bond coat is essential. Contact the TAL Technical Advice Centre for advice.
Storage & Shelf Life
- Shelf life: 6 months from date of manufacture
- Store sealed, upright, between 10°C–30°C, out of direct sunlight
- Never store directly on a concrete floor
- Secure during transport to prevent spillage
Health & Safety
For use by trained operatives only. Refer to the TAL Primercoat MSDS before purchase and use. Personal protective equipment required: gloves, safety goggles, dust mask, coveralls, rubber-soled safety shoes. Work in well-ventilated areas. Do not ingest. Dispose in accordance with local regulations. Contact TAL on 0860 000 825 or taltech@tal.co.za for a copy of the MSDS.
Authorised TAL Stockist
FlooringStore.co.za is an authorised TAL stockist. All TAL products are supplied from TAL's South African distribution network and carry the full TAL manufacturer guarantee. TAL products are manufactured under ISO 9001:2015, OHSAS 45001:2018 and ISO 14001:2018.
Downloads
Additional information
| Manufacturer | TAL |
|---|---|
| Product Type | Sub-Floor Preparation |
| Accessory Category | Primers & Sealers |
| Supplier | TAL |
| Warehouse Location | Gauteng JHB, Kwazulu-Natal Durban, Western Cape CPT |
| TAL Primercoat | Primercoat 5L Slurry |
|---|---|
| Pack size (L) | 5 |
| Coverage (m² per litre) | 5.50 |
| Shelf Life | 6 months |
Product Description
- ✅ Ready to use — no mixing required
- ✅ Rapid-drying — touch-dry in 1–2 hours
- ✅ Keys onto epoxy, polyurethane, polyurea and fibreglass surfaces
- ✅ Fully compatible with TAL cementitious underlayments and screeds
- ✅ Coverage ±5.5m² per litre (±27.5m² per 5L bucket)
When to Use TAL Primercoat
Use TAL Primercoat when laying a cementitious underlayment or screed over any resin-based surface — existing or newly applied epoxy coatings, polyurethane floors, polyurea, fibreglass, and similar impervious substrates. Without a keying slurry, cementitious products cannot bond to the smooth resin surface and will delaminate.
Pack Contents & Coverage
- Pack: 5L (7.5kg) ready-mix plastic bucket — no mixing required
- Coverage: ±5.5m² per litre / ±27.5m² per bucket (per coat)
- Application thickness: 0.2mm – 1mm
- Colour: light green wet, dries to grass-green
- Actual coverage will vary depending on surface profile and site conditions
Application
- Surface preparation (existing resin surfaces): Diamond grind to remove all dirt, grease and surface contaminants and produce an open, lightly textured surface. Solvent wipe with TAL Epoxy Cleaning Fluid.
- Clean: Vacuum or sweep all dust and loose particles thoroughly. Vacuuming is preferred.
- Stir well before use. Do not dilute with water or add any additives.
- Apply with a short-pile lambswool roller, ensuring 100% coverage of the substrate. Any gaps in coverage can result in delamination of the following layer.
- Allow to dry for 1–2 hours at 23°C / 50% RH until touch-dry with no visible transfer when rubbing over the surface.
- Apply TAL cementitious underlayment or screed compound directly onto the dried Primercoat.
Note: TAL Primercoat cures by water evaporation. Thicker applications, cold conditions or poor ventilation will extend drying time. Do not apply below 10°C or above 30°C. Do not dilute or adulterate the product in any way.
Important: For installations on post-tensioned concrete suspended slabs where significant building movement is anticipated, a wet epoxy bond coat is essential. Contact the TAL Technical Advice Centre for advice.
Storage & Shelf Life
- Shelf life: 6 months from date of manufacture
- Store sealed, upright, between 10°C–30°C, out of direct sunlight
- Never store directly on a concrete floor
- Secure during transport to prevent spillage
Health & Safety
For use by trained operatives only. Refer to the TAL Primercoat MSDS before purchase and use. Personal protective equipment required: gloves, safety goggles, dust mask, coveralls, rubber-soled safety shoes. Work in well-ventilated areas. Do not ingest. Dispose in accordance with local regulations. Contact TAL on 0860 000 825 or taltech@tal.co.za for a copy of the MSDS.
Authorised TAL Stockist
FlooringStore.co.za is an authorised TAL stockist. All TAL products are supplied from TAL’s South African distribution network and carry the full TAL manufacturer guarantee. TAL products are manufactured under ISO 9001:2015, OHSAS 45001:2018 and ISO 14001:2018.
Downloads
Product Additional Information
Additional information
| Manufacturer | TAL |
|---|---|
| Product Type | Sub-Floor Preparation |
| Accessory Category | Primers & Sealers |
| Supplier | TAL |
| Warehouse Location | Gauteng JHB, Kwazulu-Natal Durban, Western Cape CPT |
| TAL Primercoat | Primercoat 5L Slurry |
|---|---|
| Pack size (L) | 5 |
| Coverage (m² per litre) | 5.50 |
| Shelf Life | 6 months |
Product Reviews
Reviews
There are no reviews yet.
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet